Guide_3DS/_pages/ko_KR/installing-boot9strap-(ntrboot).txt

---
title: "Installing boot9strap (ntrboot)"
---

#### 준비물

* A magnet that triggers the sleep mode of your device (if using a folding style device)
* Your ntrboot flashed flashcart
* The latest release of [SafeB9SInstaller](https://github.com/d0k3/SafeB9SInstaller/releases/latest)
* The latest release of [boot9strap](https://github.com/SciresM/boot9strap/releases/latest) *(standard boot9strap; not the `devkit` file, not the `ntr` file)*
* 최신 버전의 [Luma3DS](https://github.com/AuroraWright/Luma3DS/releases/latest) *(`.7z` 파일)*
* 홈브류 [스타터 킷](http://smealum.github.io/ninjhax2/starter.zip)

#### 진행 방법

##### 섹션 I - 준비 작업

1. 기기를 종료해 주세요.
1. SD 카드를 컴퓨터에 삽입해 주세요.
1. Copy `SafeB9SInstaller.firm` to the root of your SD card and rename it to `boot.firm`
1. Copy _the contents of_ `starter.zip` to the root of your SD card
1. Create a folder named `boot9strap` on the root of your SD card
1. Copy `boot9strap.firm` and `boot9strap.firm.sha` from the boot9strap `.zip` to the `/boot9strap/` folder on your SD card

    ![]({{ base_path }}/images/screenshots/boot9strap-ntrboot-file-layout.png)
    {: .notice--info}

1. SD 카드를 기기에 다시 삽입해 주세요.
1. 기기를 시작해 주세요.

##### Section II - ntrboot

1. Use the magnet to find the spot on your device where the sleep sensor is triggered
  + This step is not needed on the old 2DS (which has a sleep mode switch)
1. 기기를 종료해 주세요.
1. Insert your flashcart into your device
1. Place the magnet on your device to trigger the sleep sensor
  + On old 2DS, you should instead enable the sleep mode switch
1. Hold (Power) + (Start) + (Select) + (X) for several seconds, then release the buttons
  + It may take a few attempts to get this to work because the positioning is awkward
1. If the exploit was successful, you will have booted into SafeB9SInstaller

##### Section III - Installing boot9strap

1. Wait for all safety checks to complete
1. When prompted, input the key combo given to install boot9strap
1. Once it has completed, force your device to power off by holding down the power button
  + Your device will only boot to the SafeB9SInstaller screen until the next section is completed

##### Section IV - Configuring Luma3DS

1. SD 카드를 컴퓨터에 삽입해 주세요.
1. Delete `boot.firm` from the root of your SD card
1. Copy `boot.firm` from the Luma3DS `.7z` to the root of your SD card
1. SD 카드를 기기에 다시 삽입해 주세요.
1. 기기를 시작해 주세요.
1. Your device should have booted into the Luma3DS configuration menu
  + If you get a black screen, [follow this troubleshooting guide](troubleshooting#ts_sys_b9s)
1. Use the (A) button and the D-Pad to turn on the following:    
  + **"Show NAND or user string in System Settings"**
1. (start)를 눌러 저장하고 기기를 다시 시작해 주세요.
  + If you get an error, just continue the next page

___

Continue to [Finalizing Setup](finalizing-setup)
{: .notice--primary}

___

##### Section V - Removing ntrboot

This is an optional section that will allow you to restore your flashcart to its original state (to allow it to be used for its standard functions).
{: .notice--info}

Do not follow this section until you have completed the rest of the instructions on this page.
{: .notice--warning}

1. Launch the Luma3DS chainloader by holding (Start) during boot on **the source 3DS**
1. Select "ntrboot_flasher"
1. Select "Restore Flash"
1. Press (Y) to proceed
1. 완료될 때까지 기다려 주세요.
1. (B)를 눌러 메인 메뉴로 돌아가 주세요.
1. Select "EXIT" to power off **the source 3DS**