Installing boot9strap (Frogtool)

若需英語支援，請於 Discord 上的 Nintendo Homebrew 伺服器發問。
如果您喜歡本教學，我們很樂意接受捐贈。
Technical Details (optional)

For technical details on the exploits that you will be using on this page, see “DSiWare_Exports CTCert verification” and “FIRM partitions known-plaintext” here.

To use the magnet link for frogcert.bin on this page, you will need a torrent client like qBittorrent or Deluge.
If you are unable to install one, follow Bannerbomb3 instead.

必備項目

  • Your movable.sed file from completing Seedminer or nimhax on the root of your SD card
  • frogcert.bin (magnet link)
  • The latest release of Frogtool
  • The latest release of b9sTool

第一節 — 檢查自製韌體

As an additional safety measure, we will perform an additional check for custom firmware. This is because using this method when custom firmware is already installed has a risk of bricking the console (rendering it unusable without recovery methods like ntrboot).

  1. 關閉您的主機
  2. 按住「Select」鍵
  3. 在開機時按住「Select」鍵
  4. If the check was successful, you will boot to the HOME Menu and you may proceed with this guide
  5. 關閉您的主機

If you see a configuration menu or the console immediately powers off, you already have CFW, and continuing with these instructions may BRICK your device! Follow Checking for CFW to upgrade your existing CFW.

第二節 — 準備工作

  1. 關閉您的主機
  2. 將 SD 卡插入至電腦中
  3. 解壓 Luma3DS .zip 內的 boot.firm 及 boot.3dsx 到 SD 卡的根目錄底下
  4. Copy boot.nds (b9sTool) from the b9sTool release .zip to the root of your SD card
  5. Copy Frogtool.3dsx to the /3ds/ folder on your SD card
  6. Copy frogcert.bin to the root of your SD card
  7. 將 SD 卡插回主機中
  8. 啟動您的主機

Section III - Patching DS Download Play

  1. Open the Homebrew Launcher through your method of choice (likely the Internet Browser)
  2. Launch Frogtool from the list of homebrew
  3. Select the “INJECT patched DS Download Play” option
  4. Frogtool will automatically run and inject the JPN version of Flipnote Studio into your DS Download Play
  5. Once this operation has finished, read the screens and check if the process was successful
  6. Tap the touch screen, then select “BOOT patched DS Download Play”
  7. 如果漏洞成功執行，您的主機將自動啟動『うごくメモ帳 (Flipnote Studio)』
    • If you get stuck on a black screen, follow this page, then try again

Section IV - Flipnote Exploit

If you would prefer a visual guide to this section, one is available here.

In this section, you will perform a series of very specific steps within Flipnote Studio that, when performed correctly, will launch the boot9strap (custom firmware) installer.

  1. Complete the initial setup process for the launched game until you reach the main menu
    • Select the left option whenever prompted during the setup process
  2. Using the touch-screen, select the large left box, then select the box with an SD card icon
  3. Once the menu loads, select the face icon, then the bottom right icon to continue
  4. Press (X) or (UP) on the D-Pad depending on which is shown on the top screen
  5. Select the second button along the top with a film-reel icon
  6. Scroll right until reel “3/3” is selected
  7. Tap the third box with the letter “A” in it
  8. Scroll left until reel “1/3” is selected
  9. Tap the fourth box with the letter “A” in it
  10. If the exploit was successful, your device will have loaded b9sTool
  11. Using the D-Pad, move to “Install boot9strap”
    • If you miss this step, the system will exit to HOME Menu instead of installing boot9strap and you will need to open Nintendo DS Connections and start over from the beginning of this section
  12. Press (A), then press START and SELECT at the same time to begin the process
  13. Once completed and the bottom screen says “done.”, exit b9sTool, then power off your device
    • You may have to force power off by holding the power button
    • If your device shuts down when you try to power it on, ensure that you have copied boot.firm from the Luma3DS .zip to the root of your SD card
    • If you see the Luma Configuration screen, power off your device and continue to the next section

Section VI - Luma3DS Configuration

  1. Your device should have booted into the Luma3DS configuration menu
    • Luma3DS configuration menu are settings for the Luma3DS custom firmware. Many of these settings may be useful for customization or debugging
    • For the purpose of this guide, leave these options on the default settings (do not check or uncheck anything)
    • If your device shuts down when you try to power it on, ensure that you have copied boot.firm from the Luma3DS .zip to the root of your SD card
  2. 按『Start』鍵以存檔並重新啟動系統

At this point, your console will boot to Luma3DS by default.

  • Luma3DS does not look any different from the normal HOME Menu. If your console has booted into the HOME Menu, it is running custom firmware.
  • On the next page, you will install useful homebrew applications to complete your setup.

Section VII - Restoring DS Connection Settings

  1. 啟動『下載通信 (Download Play)』程式
  2. 等到你看到兩個按鍵
    • Do not press either of the buttons
  3. 同時按下『L』+『下』+『Select』鍵以啟動 Rosalina 選單
  4. 選擇『Miscellaneous options』
  5. 選擇『Switch the hb. title to the current app.』
  6. 按『B』繼續
  7. 按『B』回到 Rosalina 主選單
  8. 按『B』退出 Rosalina 選單
  9. 按『Home』鍵，並關閉『下載通信 (Download Play)』程式
  10. Relaunch the Download Play application
  11. 您的主機應該就會啟動 Homebrew Launcher 了
  12. Launch Frogtool from the list of homebrew
  13. Select the “RESTORE patched DS Download Play” option
  14. Once this operation has finished, read the screens and check if the process was successful
    • If there are any errors or missing files, correct the problem and try again
  15. If the process was successful, tap the touch screen, then press START to exit
  16. 關閉您的主機

繼續至完成安裝