---
title: "Problembehandlung"
---

Diese Seite gibt Anweisungen und Lösungen für oft auftretende Fehler. Wenn diese Seite das Problem nicht lösen kann, tritt bitte [Nintendo Homebrew on Discord](https://discord.gg/MWxPgEp) und beschreibe dein Problem, zusätzlich mit dem, was du schon versucht hast.

{% capture compat %}
<summary>Inhaltsverzeichnis</summary>

Used on multiple pages:
* [SafeB9SInstaller](#issues-with-safeb9sinstaller)

Guide pages:
* [Installing boot9strap (Soundhax)](#installing-boot9strap-soundhax)
* [Installing boot9strap (MSET9)](#installing-boot9strap-mset9)
* [Installing boot9strap (SSLoth-Browser)](#installing-boot9strap-ssloth-browser)
* [Installing boot9strap (super-skaterhax)](#installing-boot9strap-super-skaterhax)
* [Finalizing Setup](#finalizing-setup)

Probleme nach der Installation:
* [Boot issues](#boot-issues-on-consoles-with-custom-firmware)
* [Software issues](#software-issues-on-consoles-with-custom-firmware)

{% endcapture %}
<details>{{ compat | markdownify }}</details>
{: .notice--info}

## Issues with SafeB9SInstaller

### Before opening SafeB9SInstaller

{% capture compat %}
<summary><u>Failed to open SafeB9SInstaller.bin</u></summary>

Die Datei `SafeB9SInstaller.bin` fehlt oder ist falsch platziert. Lade die neueste Version von [SafeB9SInstaller](https://github.com/d0k3/SafeB9SInstaller/releases/download/v0.0.7/SafeB9SInstaller-20170605-122940.zip) herunter, entpacke sie und platziere `SafeB9SInstaller.bin` im Stammverzeichnis deiner SD-Karte. Füge die `.bin` Erweiterung nicht hinzu, wenn du sie noch nicht siehst.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

### SigHaxed FIRM was not installed! Check lower screen for more info.

{% capture compat %}
<summary><u>MicroSD Card - init failed</u></summary>

Your SD card is most likely acting weird. Try reformatting your SD card ([Windows](formatting-sd-(windows)), [macOS](formatting-sd-(mac)), [Linux](formatting-sd-(linux))). If this doesn't work, try another SD card.

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>SigHaxed FIRM - File not found</u></summary>

Dir fehlt die `boot9strap.firm` und die `boot9strap.firm.sha` Datei im `boot9strap` Ordner, oder der `boot9strap` Ordner ist falsch bennant. Lade dir neuste Version von [boot9strap](https://github.com/SciresM/boot9strap/releases/download/1.4/boot9strap-1.4.zip) herunter und platziere `boot9strap.firm` und `boot9strap.firm.sha` in deinen `boot9strap` Ordner.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>SigHaxed FIRM - invalid FIRM</u></summary>

Es liegt ein Problem mit den 'boot9strap.firm' und 'boot9strap.firm.sha' Dateien vor. Lade dir neuste Version von [boot9strap](https://github.com/SciresM/boot9strap/releases/download/1.4/boot9strap-1.4.zip) herunter und platziere `boot9strap.firm` und `boot9strap.firm.sha` in deinem `boot9strap` Ordner.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Secret Sector - File not found</u></summary>

Dir fehlt die `secret_sector.bin` Datei im `boot9strap` Ordner, oder dein `boot9strap` Ordner ist falsch benannt. Lade [secret_sector.bin](magnet:?xt=urn:btih:15a3c97acf17d67af98ae8657cc66820cc58f655&dn=secret_sector.bin&tr=udp%3a%2f%2ftracker.torrent.eu.org%3a451%2fannounce&tr=udp%3a%2f%2ftracker.lelux.fi%3a6969%2fannounce&tr=udp%3a%2f%2ftracker.loadbt.com%3a6969%2fannounce&tr=udp%3a%2f%2ftracker.moeking.me%3a6969%2fannounce&tr=udp%3a%2f%2ftracker.monitorit4.me%3a6969%2fannounce&tr=udp%3a%2f%2ftracker.ololosh.space%3a6969%2fannounce&tr=udp%3a%2f%2ftracker.pomf.se%3a80%2fannounce&tr=udp%3a%2f%2ftracker.srv00.com%3a6969%2fannounce&tr=udp%3a%2f%2ftracker.theoks.net%3a6969%2fannounce&tr=udp%3a%2f%2ftracker.tiny-vps.com%3a6969%2fannounce&tr=udp%3a%2f%2fopen.tracker.cl%3a1337%2fannounce&tr=udp%3a%2f%2ftracker.zerobytes.xyz%3a1337%2fannounce&tr=udp%3a%2f%2ftracker1.bt.moack.co.kr%3a80%2fannounce&tr=udp%3a%2f%2fvibe.sleepyinternetfun.xyz%3a1738%2fannounce&tr=udp%3a%2f%2fwww.torrent.eu.org%3a451%2fannounce&tr=udp%3a%2f%2ftracker.openbittorrent.com%3a6969%2fannounce&tr=udp%3a%2f%2f9.rarbg.com%3a2810%2fannounce&tr=udp%3a%2f%2ftracker.opentrackr.org%3a1337%2fannounce&tr=udp%3a%2f%2fexodus.desync.com%3a6969%2fannounce&tr=http%3a%2f%2fopenbittorrent.com%3a80%2fannounce) mit einem Torrent Client herunter, und platziere sie in deinem `boot9strap` Ordner.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Etwas anderes</u></summary>

Tritt [Nintendo Homebrew auf Discord](https://discord.gg/MWxPgEp) bei und beschreibe die Nachricht, die du siehst.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

## Installing boot9strap (Soundhax)

{% capture compat %}
<summary><u>Red/purple/pink and white screen after running Soundhax</u></summary>

If your console is on system version 9.4.0, 9.5.0, or 9.6.0, you may be encountering a bug with an old version of universal-otherapp. Download the latest version from [here](https://github.com/TuxSH/universal-otherapp/releases/latest).

If your console is not on those firmwares, it likely indicates that you already have custom firmware. You should [check for CFW](checking-for-cfw).
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>"An error has occurred, forcing the software to close..." (white message box)</u></summary>

There is an issue with your `otherapp.bin` file (it is missing, misplaced, or corrupted). Download the latest release of [universal-otherapp](https://github.com/TuxSH/universal-otherapp/releases/latest) and place it on the root of your SD card.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>"Could not play"</u></summary>

You have the wrong Soundhax file for your console and region, or your console is incompatible with Soundhax. In the latter case, your course of action will determine on what version your 3DS is currently on. Trete [Nintendo Homebrew auf Discord](https://discord.gg/MWxPgEp) für mehr Hilfe bei.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Failed to mount the SD card!</u></summary>
Sichere deine Daten und formatiere deine SD-Karte als FAT32 mit dem empfohlenen Werkzeug je nach Betriebssystem ([Windows](formatting-sd-(windows)), [macOS](formating-sd-(mac)), [Linux](formating-sd-(linux))). MiniTool Partition Wizard und das HP Formatierungswerkzeug (HPUSBDisk) sind bekannt für Probleme mit 3DS SD-Karten.

Wenn dies nicht gelingt, benutze eine andere SD-Karte.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

## Installing boot9strap (MSET9)

{% capture compat %}
<summary><u>Python 3 is not installed</u></summary>

Python is not installed on the computer you are using. Download it from the [Python website](https://www.python.org/downloads/), double-click the installer, and follow the prompts to install Python. Once Python is installed, try again.

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error 01: Couldn't find Nintendo 3DS folder</u></summary>

You are not running MSET9 from the root of the SD card, or the SD card is missing the Nintendo 3DS folder.

Remember, your SD card should look like this:

![MSET9 root layout](/images/screenshots/mset9/mset9-root-layout.png)
{: .notice--info}

If your SD card layout is correct, then your SD card most likely isn't being read by your console. Re-format it ([Windows](formatting-sd-(windows)), [Linux](formatting-sd-(linux)), [macOS](formatting-sd-(mac))), then start again from the beginning of [Section I](installing-boot9strap-(mset9)#section-i---prep-work).

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error 02: Your SD is write protected</u></summary>

Write-protection is enabled on this SD card. If you are using a full-size SD card, ensure that the lock is flipped in the [upright position](/images/sdlock.png). Otherwise, try ejecting and reinserting your SD card.

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error 03: Don't change console version</u></summary>

You inputted a different number between different runs of MSET9 (for example, you initially selected option 1 for "Old 3DS, 11.8 - 11.17" and then later selected option 2 for "New 3DS, 11.8 - 11.17").

If this happened when trying to uninstall MSET9, the script has automatically removed MSET9 for you and you can continue to the next page. Otherwise, start again from the beginning of [Section I](installing-boot9strap-(mset9)#section-i---prep-work).

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error 04: No HOME Menu Extdata.</u></summary>

Your SD card is not formatted properly.

Copy everything off the SD Card to your PC, re-format it ([Windows](formatting-sd-(windows)), [Linux](formatting-sd-(linux)), [macOS](formatting-sd-(mac))), copy everything back, then start again from the beginning of [Section I](installing-boot9strap-(mset9)#section-i---prep-work).

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error 05: No Mii Maker Data!</u></summary>

Mii Maker data was not found on the SD card. Start again from the beginning of [Section I](installing-boot9strap-(mset9)#section-i---prep-work).

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error 06: You need at least 16MB free</u></summary>

Your SD card does not have enough space to trigger MSET9. Free up some space and try again.

At the end of this guide, you will need at least 1.3GB to make a NAND backup, so it's best to free up at least that much.

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error 07: You don't have 1 ID0, you have (#)!</u></summary>

You have multiple ID0 folders. To determine the correct folder, follow these instructions:

1. Benenne den `Nintendo 3DS` Ordner zu `BACKUP_Nintendo 3DS` um
1. Reinsert your SD card into your console
1. Power on your console
1. Wait for the console to generate the SD card data
    + Deine Apps werden verschwunden sein. Das ist normal und wird gleich behoben
1. Power off your console
1. Stecke deine SD-Karte in deinen Computer
1. Navigiere zum "Nintendo 3DS"-Ordner auf deiner SD-Karte
1. Write down the first few characters of the folder you see
    + This is your true ID0, which we will keep in the real Nintendo 3DS folder
1. Delete the ID0 from the current `Nintendo 3DS` folder
1. Move the true ID0 folder from the `BACKUP_Nintendo 3DS` folder to the `Nintendo 3DS` folder
1. If it exists, move the `Private` folder from the `BACKUP_Nintendo 3DS` folder to the `Nintendo 3DS` folder

Once you've done this, continue from [Section I Step 7](installing-boot9strap-(mset9)#section-i---prep-work).

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error 08: One or more files are missing or malformed!</u></summary>

One or more files that MSET9 needs to run is missing or corrupted. Re-download the [MSET9 Release `.zip`](https://github.com/zoogie/MSET9/releases/latest) and extract it to the root of your SD card, replacing all existing files, then try again.

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error 10: Database(s) malformed or missing!</u></summary>

This happens when no valid title database is present, usually because you never installed any titles from eShop on this SD card.

1. If you haven't already, press Enter to close the MSET9 script
1. Insert the SD card into your console
1. Power on your console
1. Navigate to System Settings -> Data Management -> Nintendo 3DS -> Software -> Reset ([visual instructions](/images/screenshots/database-reset.jpg))
1. Power off your console
1. Insert the SD card into your computer
1. Return to [Section I Step 7](installing-boot9strap-(mset9)#section-i---prep-work)

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error 12: You don't have 1 ID1, you have (#)!</u></summary>

{% include_relative include/id1-check.txt %}

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Red screen after reinserting SD card (Section II Step 11)</u></summary>

You may be missing `SafeB9S.bin` from the root of your SD card, or the file may be corrupted. Copy it from the MSET9 `.zip`, replacing any existing files.

Alternatively, your SD card may be improperly formatted or partitioned. Try reformatting your SD card: [Windows](formatting-sd-(windows)), [Linux](formatting-sd-(linux)), [macOS](formatting-sd-(mac)) *(this will wipe your SD card data)*

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>System Settings loading infinitely after reinserting the SD card</u></summary>

You most likely did something different from the MSET9 instructions, or selected the wrong model or version.

1. Close the script window
1. Execute the `mset9.py` script on the root of the SD card
    + **Windows**: Double-click `mset9.bat`
    + **Linux**: open a Terminal window, `cd` to the root of your SD card, then type `python3 mset9.py` and press Enter
    + You should see a window that says "MSET9 ... SETUP by zoogie"
1. Type the number corresponding to your console model and version, then press Enter
1. Type `3`, then press Enter
1. Once the window says "Successfully removed MSET9!", reinsert the SD card into your console
1. Power on your console
1. Return to [Section II Step 1](installing-boot9strap-(mset9)#section-ii---mset9)

If you continue to have this issue and are sure that you did everything correctly, it's possible that there's something wrong with your Mii Maker extdata. Follow these instructions to reset it:

1. Close the script window
1. Run the MSET9 script
    + **Windows**: Double-click `mset9.bat`
    + **Linux**: open a Terminal window, `cd` to the root of your SD card, then type `python3 mset9.py` and press Enter
    + You should see a window that says "MSET9 ... SETUP by zoogie"
1. Type the number corresponding to your console model and version, then press Enter
1. Type `3`, then press Enter to remove MSET9
1. If possible, use a new SD card; otherwise, backup and reformat your existing SD card as FAT32 ([Windows](formatting-sd-(windows)), [Linux](formatting-sd-(linux)), [macOS](formatting-sd-(mac)))
1. Insert the formatted, blank SD card into your console
1. Return to [Section I Step 1](installing-boot9strap-(mset9)#section-i---prep-work)

After finishing the MSET9 page, you should switch back to your old SD card before continuing to Finalizing Setup.
{: .notice--warning}

{% endcapture %}
<details>{{ compat | markdownify }}</details>

## Installing boot9strap (super-skaterhax)

{% capture compat %}
<summary><u>"An error has occurred. Please save your data in any software currently in use, then restart the system."</u></summary>

The date is set incorrectly. To set it correctly, follow these steps:

1. Select the System Settings icon on the HOME Menu, and tap Open.
1. Tap Other Settings.
1. Tap Date & Time.
1. Tap Today's date.
1. Tap Up/Down Arrows to set the correct Day, Month and Year.
1. Select OK to confirm.

If the problem persists:

+ Ensure that `arm11code.bin`, `browserhax_hblauncher_ropbin_payload.bin`, and `boot.3dsx` are on the root of the SD card (not inside of any folder)
+ Ensure that you selected the correct payload for your region AND system version
+ Ensure that your region settings look [like this](/images/screenshots/skater_lang.png)
+ Try resetting your browser data:
    1. Launch the browser, then launch the browser settings
    1. Scroll to the bottom and select "Reset Save Data" (it may also be called "Initilize Save Data" or "Clear All Save Data")
    1. Try the exploit again
+ Try changing the system language to something other than the current language

{% endcapture %}
<details>{{ compat | markdownify }}</details>


{% capture compat %}
<summary><u>"An error has occurred. Hold down the POWER button to turn off the power..." (black screen with text)</u></summary>

The file `arm11code.bin` is missing or misplaced. Make sure to copy the files of the [latest version of super-skaterhax](https://github.com/zoogie/super-skaterhax/releases/latest) for your region and version to the root of your SD card (not inside of a folder).

![]({{ "/images/screenshots/skater-root-layout.png" | absolute_url }})
{: .notice--info}

{% endcapture %}
<details>{{ compat | markdownify }}</details>


{% capture compat %}
<summary><u>An exception occured or "DLL_HEAP_INFORMATION" when pressing GO! GO!</u></summary>

This likely indicates that you already have custom firmware. You should [check for CFW](checking-for-cfw).

{% endcapture %}
<details>{{ compat | markdownify }}</details>

## Installing boot9strap (SSLoth-Browser)

{% capture compat %}
<summary><u>Red/purple/pink and white screen after running Browserhax</u></summary>

This likely indicates that you already have custom firmware. You should [check for CFW](checking-for-cfw).
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>"An error has occurred. Hold down the POWER button to turn off the power..." (black screen with text)</u></summary>

The file `arm11code.bin` is missing or misplaced. Lade die neuste Version von [universal-otherapp](https://github.com/TuxSH/universal-otherapp/releases/latest) herunter, platziere `otherapp.bin` im Stammverzeichnis deiner SD-Karte und benenne die Datei zu `arm11code.bin` um. Füge die `.bin` Erweiterung nicht hinzu, wenn du sie noch nicht siehst.
{% endcapture %}
<details>{{ compat | markdownify }}</details>


{% capture compat %}
<summary><u>"An error has occurred, forcing the software to close..." (white message box)</u></summary>

There may be an issue with your `arm11code.bin` file. Lade die neuste Version von [universal-otherapp](https://github.com/TuxSH/universal-otherapp/releases/latest) herunter, platziere `otherapp.bin` im Stammverzeichnis deiner SD-Karte und benenne die Datei zu `arm11code.bin` um. Füge die `.bin` Erweiterung nicht hinzu, wenn du sie noch nicht siehst.

You can also try resetting your browser save data:

1. Launch the browser, then launch the browser settings
1. Scroll to the bottom and select "Reset Save Data" (it may also be called "Initialize Save Data" or "Clear All Save Data")
1. Try the exploit again

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Opening the browserhax QR code or URL crashes</u></summary>

Browser based exploits (such as this one) are often unstable and crash frequently, but they can sometimes be fixed by doing the following steps.

1. Launch the browser, then launch the browser settings
1. Scroll to the bottom and select "Reset Save Data" (it may also be called "Initialize Save Data" or "Clear All Save Data")
1. Try the exploit again
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>System Update prompt when opening browser</u></summary>

The SSLoth proxy was incorrectly configured. Re-do the SSLoth section on the page.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error 032-0420 when opening browser</u></summary>

Follow these steps in order:

1. Launch System Settings on your console
1. Navigate to `Internet Settings` -> `Connection Settings`
1. Click on your network connection slot and navigate to `Change Settings` -> `Next Page (right arrow)` -> `Proxy Settings`
1. Set "Proxy Settings" to "No"
1. Click OK, then click Save
1. When prompted, click "Test" to perform the connection test
    + Der Test sollte erfolgreich sein
1. Click "OK" to continue
1. Press "Back" twice, then "Close" to go back to the HOME Menu
1. Open the Internet Browser once
1. If prompted about a system update, press OK
    + This won't actually update the system
1. Start again from [Section II](installing-boot9strap-(ssloth-browser).html#section-ii---ssloth)
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Frozen on "Doing agbhax..."</u></summary>
There may be an issue with your `arm11code.bin` file. Re-download the latest release of [universal-otherapp](https://github.com/TuxSH/universal-otherapp/releases/latest), place it on the root of your SD card, and rename it to `arm11code.bin`. Füge die `.bin` Erweiterung nicht hinzu, wenn du sie noch nicht siehst.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>"PrepareArm9ForTwl returned error c8804631!"</u></summary>

Trete [Nintendo Homebrew auf Discord](https://discord.gg/MWxPgEp) für mehr Hilfe bei.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Failed to mount the SD card!</u></summary>

Sichere deine Daten und formatiere deine SD-Karte als FAT32 mit dem empfohlenen Werkzeug je nach Betriebssystem ([Windows](formatting-sd-(windows)), [macOS](formating-sd-(mac)), [Linux](formating-sd-(linux))). MiniTool Partition Wizard und das HP Formatierungswerkzeug (HPUSBDisk) sind bekannt für Probleme mit 3DS SD-Karten.

Wenn dies nicht gelingt, benutze eine andere SD-Karte.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

## Finalizing Setup

{% capture compat %}
<summary><u>Unable to update console</u></summary>

The steps below can be attempted in any order, but are listed from easiest to hardest to perform.

1. Set your DNS settings to "Auto"
1. Move closer to your WiFi router
1. Update from Safe Mode by turning off the console, holding (Left Shoulder) + (Right Shoulder) + (D-Pad Up) + (A) on boot, and following the on-screen prompts
1. Delete your WiFi connection, then reconnect to your WiFi again
1. Reboot your WiFi router
1. Connect to a different WiFi connection, like a mobile hotspot
1. Nintendo servers may be down; Try again later
1. If you still get an error, [follow CTRTransfer](ctrtransfer), then try again
1. For further support (in English), join [Nintendo Homebrew on Discord](https://discord.gg/MWxPgEp)
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error #02: Missing essential.exefs</u></summary>

You said 'No' to the "Make essential files backup?" prompt in GodMode9. Power off your console, power it on while holding (Start) to re-enter GodMode9, say 'Yes' to the prompt, then try again.

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}

<summary><u>Unable to open GodMode9 or Error #03: Missing files</u></summary>

You did not copy everything from `finalize.zip` to the root of your SD card. Remember, your SD card should have at least these files:

![]({{ "/images/screenshots/finalizing-root-layout.png" | absolute_url }})
{: .notice--info}

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}

<summary><u>Error #04: No space</u></summary>

You need at least 1.3GB of free space to perform the NAND backup, which is a part of the script. If you don't have enough space, follow these steps:

1. Power off your console
1. Stecke deine SD-Karte in deinen Computer
1. Copy the `Nintendo 3DS` folder from the root of your SD card to your computer
1. Delete the Nintendo 3DS folder from the SD card
1. Reinsert your SD card into your console
1. Press and hold (Start), and while holding (Start), power on your console. This will launch GodMode9
1. Press the (Home) button
1. Wähle "Scripts"
1. Select "finalize"
1. Press (A) to create a NAND backup
    + This may take around fifteen minutes
1. Press (A) again
    + The console should automatically power off
1. Stecke deine SD-Karte in deinen Computer
1. Copy the files in `/gm9/backups/` on your SD to a safe location on your computer
1. Delete the `<date>_<serialnumber>_sysnand_##.bin` and `<date>_<serialnumber>_sysnand_##.bin.sha` files from the SD card
1. Copy the `Nintendo 3DS` folder from your computer to the root of your SD card
1. Delete the `Nintendo 3DS` folder from your computer

Now that you have your NAND backup in a safe place:

1. Reinsert your SD card into your console
1. Press and hold (Start), and while holding (Start), power on your console. This will launch GodMode9
1. Press the (Home) button
1. Wähle "Scripts"
1. Select "finalize"
1. Continue the script as normal
    + The NAND backup will be automatically skipped

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Information #05: No title database</u></summary>

Press (A) to import a title database, unlock SysNAND writing by entering the buttons on-screen, then continue the script as normal.

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error #06 or "Error: Could not open directory" when attempting a NAND backup</u></summary>

Make sure you have at least 1.3GB available in your SD card. If you don't have enough space, follow these steps:
1. Power off your console
1. Stecke deine SD-Karte in deinen Computer
1. Copy the `Nintendo 3DS` folder from the root of your SD card to your computer
1. Delete the Nintendo 3DS folder from the SD card
1. Reinsert your SD card into your console
1. Press and hold (Start), and while holding (Start), power on your console. This will launch GodMode9
1. Perform a [NAND Backup](godmode9-usage#creating-a-nand-backup)
1. Copy the files in `gm9/out` on your SD to a safe location on your computer
1. Delete the `<date>_<serialnumber>_sysnand_##.bin` and `<date>_<serialnumber>_sysnand_##.bin.sha` files from the SD card, keeping essential.exefs in `/gm9/out/`
1. Copy the `Nintendo 3DS` folder from your computer to the root of your SD card
1. Delete the `Nintendo 3DS` folder from your computer

If you have enough space on your SD card, your SD might be corrupted or faulty. Check your SD card for any errors by following the guide according to your computer's operating system: [Windows](h2testw-(windows)), [Linux](f3-(linux)), [macOS](f3xswift-(mac)).
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error #09: Unsupported GodMode9 version</u></summary>

You are somehow running a version of GodMode9 not packaged with the script. Make sure you copied the contents of `finalize.zip` to the root of your SD card and that you are holding START while powering on your console.

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error #11: Missing donor database</u></summary>

You did not copy everything from `finalize.zip` to the root of your SD card. Remember, your SD card should have at least these files:

![]({{ "/images/screenshots/finalizing-root-layout.png" | absolute_url }})
{: .notice--info}

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error #12: Copy (file).db fail</u></summary>

Ensure that your SD card is not [locked](/images/sdlock.png). If the SD card is not locked and you continue to get this error, join [Nintendo Homebrew on Discord](https://discord.gg/MWxPgEp) for assistance.

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Information #17: Duplicate NAND backup</u></summary>

The script has detected that the Nintendo 3DS folder is missing AND that you have already made a NAND backup before. If you intend to install homebrew applications, you should do the following:

1. Press (B) to cancel making another NAND backup
1. Hold (R) and press (Start) at the same time to power off your console
1. Copy the contents of `/gm9/backups/` to a safe location on your computer
1. Delete `/gm9/backups/` from your SD card
1. If you moved your Nintendo 3DS folder off of your SD card to get to this point, copy it back to your SD card
    + If you do not have a Nintendo 3DS folder, boot into the HOME Menu at least once with the SD card inserted to automatically generate it
1. Press and hold (Start), and while holding (Start), power on your console. This will launch GodMode9
1. Drücke (Home), um das Aktionsmenü aufzurufen
1. Wähle "Scripts"
1. Select "finalize"
1. Follow the prompts in the script, answering any questions that you are asked 

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Error #18: MSET9 detected</u></summary>

You didn't remove MSET9 when prompted to. Follow [Section IV - Removing MSET9](installing-boot9strap-(mset9)#section-iv---removing-mset9), then re-run the script.

{% endcapture %}
<details>{{ compat | markdownify }}</details>

---

## Boot issues on consoles with custom firmware

The steps detailed here generally assume that your console has a modern custom firmware setup (boot9strap + Luma3DS 8.0 or greater). If your console is running an older homebrew setup (for example, something based on arm9loaderhax or menuhax), you should update your setup before trying these instructions.
{: .notice--info}

### Power/notification light indicators

{% capture compat %}
<summary><u>My console powers off when I try to turn it on, and/or the notification LED shows a color on boot</u></summary>

There is an issue with your `boot.firm` file. If you're running [boot9strap 1.4](https://github.com/SciresM/boot9strap/releases/tag/1.4), your 3DS notification LED may flash a certain color. This color is used to diagnose issues involving your `boot.firm` file on SD card or internal memory. On older versions of boot9strap, the blue light will power off almost immediately when trying to turn on the console.

If the notification LED flashes:

+ **White**: Your 3DS was not able to find `boot.firm` on your SD card or on internal memory.
+ **Magenta**: Your 3DS was not able to find `boot.firm` on your SD card. It was able to find `boot.firm` on internal memory, but the file is corrupted.
+ **Red**: Your 3DS was able to find `boot.firm` on both your SD card and on internal memory, but both files are corrupted.

You can get a new `boot.firm` file by downloading the [latest release of Luma3DS](https://github.com/LumaTeam/Luma3DS/releases/latest), extracting it, and placing `boot.firm` on the root of your SD card. If your `boot.firm` file is consistently being detected as corrupted, you may want to check your SD card for errors ([Windows](h2testw-(windows)), [Linux](f3-(linux)), or [macOS](f3xswift-(mac))). Also, note that the 3DS tends to have issues with files extracted using WinRAR.

If you hear a "popping sound", potentially accompanied with the backlight turning on for a split second, there is a hardware issue with your console (such as a disconnected backlight cable). You may be able to get your console to boot by holding it at certain angles.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>My console gets stuck on a black screen with blue power light staying on</u></summary>

The steps below can be attempted in any order, but are listed from least to most time-consuming.

1. Power off your console, remove the SD card, re-insert it, then power on your console.
1. Power off your console, eject the game cartridge if inserted, power on your console, then wait up to ten minutes. If your console boots within ten minutes, the issue has been fixed and is unlikely to reoccur
1. Rename the `Nintendo 3DS` folder on your SD card to `Nintendo 3DS_BACKUP`, then attempt to boot. If your console successfully boots, there is some issue within your `Nintendo 3DS` folder. Try clearing HOME Menu extdata:
    + Navigate to `/Nintendo 3DS/<ID0>/<ID1>/extdata/00000000/`
    + Delete the corresponding folder for your 3DS region:
        + **EUR-Region**: `00000098`
        + **JPN-Region**: `00000082`
        + **USA-Region**: `0000008f`
        + **CHN-Region**: `000000A1`
        + **KOR-Region**: `000000A9`
        + **TWN-Region**: `000000B1`
1. Try booting into recovery mode and updating your system:
    + Power off your console
    + Hold (Left Shoulder) + (Right Shoulder) + (D-Pad Up) + (A)
    + Power on your console
    + If you were successful, the console will boot to an "update your system" screen
1. Follow the [CTRTransfer](ctrtransfer) guide
1. For further support, ask for help at [Nintendo Homebrew on Discord](https://discord.gg/MWxPgEp)
{% endcapture %}
<details>{{ compat | markdownify }}</details>

### Error message on boot

{% capture compat %}
<summary><u>"An error has occurred: Failed to apply 1 FIRM patch(es)" or "An exception has occurred -- Current process: pm"</u></summary>

Your Luma3DS version is outdated. Download the latest release of [Luma3DS](https://github.com/LumaTeam/Luma3DS/releases/latest) and place `boot.firm` on the root of your SD card, replacing any existing file. Make sure you are extracting the ZIP file with any tool other than WinRAR, as it is known to cause issues with 3DS-related files.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>"Unable to mount CTRNAND or load the CTRNAND FIRM. Please use an external one."</u></summary>
There are a number of reasons as to why this could be happening. In any case, this error can usually be fixed by following the [CTRTransfer](ctrtransfer) guide.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>"An error has occurred. Hold down the POWER button to turn off the power..."</u></summary>

ARM11 exception handlers are disabled, or custom firmware is not installed. Try enabling ARM11 exception handlers:
    + Power off your console
    + Hold (Select)
    + Power on your console, while still holding (Select)
    + If the "Disable ARM11 exception handlers" box is checked, uncheck it
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>HOME Menu is missing installed applications</u></summary>

This could be caused by various reasons, but most likely because your SD card is not being read by the system.
You can check if your SD is being read by holding SELECT on boot and checking the yellow text on the bottom screen; if it says "Booted from CTRNAND via B9S", then your console is booting from the internal memory and not from the SD card.
If this is the case, attempt the steps below, which are listed from easiest to hardest:
1. Power off your console, remove the SD card, re-insert it, then power on your console
1. Power off your console, remove the SD card, insert it on your computer, download the latest release of [Luma3DS](https://github.com/LumaTeam/Luma3DS/releases/latest), extract `boot.firm` from the `Luma3DS.zip` and place it on the root of your SD card (replacing any existing file)
1. Power off your console, remove the SD card, insert it on your computer and reformat your SD card according to your computer's operating system: [Windows](formatting-sd-(windows)), [macOS](formatting-sd-(mac)), [Linux](formatting-sd-(linux)) *(this will wipe your SD card data)*
1. Test your SD card for errors by following the guide according to your computer's operating system: [Windows](h2testw-(windows)), [Linux](f3-(linux)), [macOS](f3xswift-(mac)). If your SD card is marked as faulty, then you will have to replace your SD card
1. Your SD card slot may be broken. Join [Nintendo Homebrew on Discord](https://discord.gg/MWxPgEp) for further assistance
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Blue "BOOTROM ERROR" screen</u></summary>

Your console is likely hard-bricked. You will need to buy an ntrboot flashcart to reinstall boot9strap in order to attempt to fix your console. This may also indicate a hardware issue that cannot be fixed. In any case, join [Nintendo Homebrew on Discord](https://discord.gg/MWxPgEp) for assistance.
    + It is also possible that someone has set a boot-time splash screen that just looks like a brick. Try leaving your console powered on, waiting on the blue screen, for five minutes.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Some other error</u></summary>

Please take a photo of the error and join [Nintendo Homebrew on Discord](https://discord.gg/MWxPgEp) for assistance.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

## Software issues on consoles with custom firmware

{% capture compat %}
<summary><u>DSi / DS functionality is broken or has been replaced with Flipnote Studio</u></summary>

1. Download the latest release of [TWLFix-CFW](https://github.com/MechanicalDragon0687/TWLFix-CFW/releases/latest) (the `.3dsx` file)
1. Power off your console
1. Erstelle einen Ordner namens `3ds` im Stammverzeichnis deiner SD-Karte falls er noch nicht existiert
1. Copy `TWLFix-CFW.3dsx` to the `/3ds/` folder on your SD card
1. Reinsert your SD card into your console
1. Open the Homebrew Launcher
1. Launch TWLFix-CFW from the list of homebrew
1. Press (A) to uninstall the broken TWL titles
1. Press (Start) to reboot the console
1. Update your console by going to System Settings, then "Other Settings", then going all the way to the right and using "System Update"
    + The update will see that the essential TWL titles have been uninstalled, and will redownload and reinstall them
1. Once the update is complete, tap "OK" to reboot the console
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>GBA Virtual Console and/or Safe Mode functionality is broken</u></summary>

Your console is running Luma3DS 6.6 or older, likely via arm9loaderhax. You should follow [A9LH to B9S](a9lh-to-b9s) to update your console to a modern custom firmware environment.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Extended memory mode games (Pokemon Sun/Moon, Smash, etc.) don't work</u></summary>

This can occur after a CTRTransfer or region change on Old 3DS / 2DS. You will need to system format your console to fix this issue.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Exception screen when booting/loading an application</u></summary>

Look for your exception screen in [this page](https://wiki.hacks.guide/wiki/3DS:Error_screens/Luma3DS_exception_screen).
If you weren't able to find your error or the instructions didn't work, join [Nintendo Homebrew on Discord](https://discord.gg/MWxPgEp) for further assistance.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Opening the HOME Menu settings crashes the console or loads the Homebrew Launcher</u></summary>

Your console likely still has menuhax67 installed. To uninstall menuhax67, download the latest release of [menuhax67](https://github.com/zoogie/menuhax67/releases/latest) (the menuhax `.zip`), then follow the ["Uninstall menuhax67" section](https://wiki.hacks.guide/wiki/3DS:Alternate_Exploits/menuhax67#Uninstall_menuhax67) here.
{% endcapture %}
<details>{{ compat | markdownify }}</details>

---

## Other troubleshooting

{% capture compat %}
<summary><u>Clear HOME Menu extdata</u></summary>

1. Power off your console
1. Stecke deine SD-Karte in deinen Computer
1. Navigate to the `/Nintendo 3DS/<ID0>/<ID1>/extdata/00000000/` folder on your SD card
1. Delete the corresponding folder for your 3DS region:
    + **EUR-Region**: `00000098`
    + **JPN-Region**: `00000082`
    + **USA-Region**: `0000008f`
    + **CHN-Region**: `000000A1`
    + **KOR-Region**: `000000A9`
    + **TWN-Region**: `000000B1`
1. Reinsert your SD card into your console
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Clear HOME Menu theme data</u></summary>

1. Power off your console
1. Stecke deine SD-Karte in deinen Computer
1. Navigate to the `/Nintendo 3DS/<ID0>/<ID1>/extdata/00000000/` folder on your SD card
1. Delete the corresponding folder for your 3DS region:
    + **EUR Region**: `000002ce`
    + **JPN Region**: `000002cc`
    + **USA Region**: `000002cd`
1. Reinsert your SD card into your console
{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Manually entering Homebrew Launcher</u></summary>

If you are missing the Homebrew Launcher application from your HOME Menu, you can follow these instructions to manually enter the Homebrew Launcher. (You will need [boot.3dsx and boot.firm](https://github.com/LumaTeam/Luma3DS/releases/latest) on the root of your SD card.)

{% include_relative include/launch-hbl-dlp.txt %}

{% endcapture %}
<details>{{ compat | markdownify }}</details>

{% capture compat %}
<summary><u>Turning off Parental Controls</u></summary>

You can disable the Parental Controls feature by going to System Settings -> Parental Controls and inserting the PIN, then pressing "Clear Settings", then "Delete" to remove it.
However, if you do not know the PIN and therefore cannot access the console's settings, you will need to disable it. In order to do this, you need to obtain your console's master key (mkey):
1. Go to [this website](https://mkey.eiphax.tech/)
1. Fill the following boxes with the information:
    + Device Type: Select "3DS" (the same applies if you are using a 2DS, New 3DS (XL/LL) or New 2DS (XL/LL))
    + System Date: The day and month your console's clock is set to
    + Inquiry Number: Can be obtained by pressing "Forgot PIN" then "I Forgot" in the Parental Controls screen
1. After you have obtained your mkey, press OK on the screen you have obtained your Inquiry Number, then input the master key
1. Press "Clear Settings", then "Delete" to remove all Parental Controls data
{% endcapture %}
<details>{{ compat | markdownify }}</details>