xz-archive/doc/liblzma-security.txt

Using liblzma securely
----------------------

0. Introduction

    This document discusses how to use liblzma securely. There are issues
    that don't apply to zlib or libbzip2, so reading this document is
    strongly recommended even for those who are very familiar with zlib
    or libbzip2.

    While making liblzma itself as secure as possible is essential, it's
    out of scope of this document.


1. Memory usage

    The memory usage of liblzma varies a lot.


1.1. Problem sources

1.1.1. Block coder

    The memory requirements of Block encoder depend on the used filters
    and their settings. The memory requirements of the Block decoder
    depend on the which filters and with which filter settings the Block
    was encoded. Usually the memory requirements of a decoder are equal
    or less than the requirements of the encoder with the same settings.

    While the typical memory requirements to decode a Block is from a few
    hundred kilobytes to tens of megabytes, a maliciously constructed
    files can require a lot more RAM to decode. With the current filters,
    the maximum amount is about 7 GiB. If you use multi-threaded decoding,
    every Block can require this amount of RAM, thus a four-threaded
    decoder could suddenly try to allocate 28 GiB of RAM.

    If you don't limit the maximum memory usage in any way, and there are
    no resource limits set on the operating system side, one malicious
    input file can run the system out of memory, or at least make it swap
    badly for a long time. This is exceptionally bad on servers e.g.
    email server doing virus scanning on incoming messages.


1.1.2. Metadata decoder

    Multi-Block .lzma files contain at least one Metadata Block.
    Externally the Metadata Blocks are similar to Data Blocks, so all
    the issues mentioned about memory usage of Data Blocks applies to
    Metadata Blocks too.

    The uncompressed content of Metadata Blocks contain information about
    the Stream as a whole, and optionally some Extra Records. The
    information about the Stream is kept in liblzma's internal data
    structures in RAM. Extra Records can contain arbitrary data. They are
    not interpreted by liblzma, but liblzma will provide them to the
    application in uninterpreted form if the application wishes so.

    Usually the Uncompressed Size of a Metadata Block is small. Even on
    extreme cases, it shouldn't be much bigger than a few megabytes. Once
    the Metadata has been parsed into native data structures in liblzma,
    it usually takes a little more memory than in the encoded form. For
    all normal files, this is no problem, since the resulting memory usage
    won't be too much.

    The problem is that a maliciously constructed Metadata Block can
    contain huge amount of "information", which liblzma will try to store
    in its internal data structures. This may cause liblzma to allocate
    all the available RAM unless some kind of resource usage limits are
    applied.

    Note that the Extra Records in Metadata are always parsed but, but
    memory is allocated for them only if the application has requested
    liblzma to provide the Extra Records to the application.


1.2. Solutions

    If you need to decode files from untrusted sources (most people do),
    you must limit the memory usage to avoid denial of service (DoS)
    conditions caused by malicious input files.

    The first step is to find out how much memory you are allowed consume
    at maximum. This may be a hardcoded constant or derived from the
    available RAM; whatever is appropriate in the application.

    The simplest solution is to use setrlimit() if the kernel supports
    RLIMIT_AS, which limits the memory usage of the whole process.
    For more portable and fine-grained limitting, you can use
    memory limitter functions found from <lzma/memlimit.h>.


1.2.1. Encoder

    lzma_memory_usage() will give you a rough estimate about the memory
    usage of the given filter chain. To dramatically simplify the internal
    implementation, this function doesn't take into account all the small
    helper data structures needed in various places; only the structures
    with significant memory usage are taken into account. Still, the
    accuracy of this function should be well within a mebibyte.

    The Subblock filter is a special case. If a Subfilter has been
    specified, it isn't taken into account when lzma_memory_usage()
    calculates the memory usage. You need to calculate the memory usage
    of the Subfilter separately.

    Keeping track of Blocks in a Multi-Block Stream takes a few dozen
    bytes of RAM per Block (size of the lzma_index structure plus overhead
    of malloc()). It isn't a good idea to put tens of thousands of Blocks
    into a Stream unless you have a very good reason to do so (compressed
    dictionary could be an example of such situation).

    Also keep the number and sizes of Extra Records sane. If you produce
    the list of Extra Records automatically from some untrusted source,
    you should not only validate the content of these Records, but also
    their memory usage.


1.2.2. Decoder

    A single-threaded decoder should simply use a memory limitter and
    indicate an error if it runs out of memory.

    Memory-limitting with multi-threaded decoding is tricky. The simple
    solution is to divide the maximum allowed memory usage with the
    maximum allowed threads, and give each Block decoder their own
    independent lzma_memory_limitter. The drawback is that if one Block
    needs notably more RAM than any other Block, the decoder will run out
    of memory when in reality there would be plenty of free RAM.

    An attractive alternative would be using shared lzma_memory_limitter.
    Depending on the application and the expected type of input, this may
    either be the best solution or a source of hard-to-repeat problems.
    Consider the following requirements:
      - You use at maximum of n threads.
      - x(i) is the decoder memory requirements of the Block number i
        in an expected input Stream.
      - The memory limitter is set to higher value than the sum of n
        highest values x(i).

    (If you are better at explaining the above conditions, please
    contribute your improved version.)

    If the above conditions aren't met, it is possible that the decoding
    will fail unpredictably. That is, on the same machine using the same
    settings, the decoding may sometimes succeed and sometimes fail. This
    is because sometimes threads may run so that the Blocks with highest
    memory usage are tried to be decoded at the same time.

    Most .lzma files have all the Blocks encoded with identical settings,
    or at least the memory usage won't vary dramatically. That's why most
    multi-threaded decoders probably want to use the simple "separate
    lzma_memory_limitter for each thread" solution, possibly fallbacking
    to single-threaded mode in case the per-thread memory limits aren't
    enough in multi-threaded mode.

FIXME: Memory usage of Stream info.

[

]


2. Huge uncompressed output

2.1. Data Blocks

    Decoding a tiny .lzma file can produce huge amount of uncompressed
    output. There is an example file of 45 bytes, which decodes to 64 PiB
    (that's 2^56 bytes). Uncompressing such a file to disk is likely to
    fill even a bigger disk array. If the data is written to a pipe, it
    may not fill the disk, but would still take very long time to finish.

    To avoid denial of service conditions caused by huge amount of
    uncompressed output, applications using liblzma should use some method
    to limit the amount of output produced. The exact method depends on
    the application.

    All valid .lzma Streams make it possible to find out the uncompressed
    size of the Stream without actually uncompressing the data. This
    information is available in at least one of the Metadata Blocks.
    Once the uncompressed size is parsed, the decoder can verify that
    it doesn't exceed certain limits (e.g. available disk space).

    When the uncompressed size is known, the decoder can actively keep
    track of the amount of output produced so far, and that it doesn't
    exceed the known uncompressed size. If it does exceed, the file is
    known to be corrupt and an error should be indicated without
    continuing to decode the rest of the file.

    Unfortunately, finding the uncompressed size beforehand is often
    possible only in non-streamed mode, because the needed information
    could be in the Footer Metdata Block, which (obviously) is at the
    end of the Stream. In purely streamed mode decoding, one may need to
    use some rough arbitrary limits to prevent the problems described in
    the beginning of this section.


2.2. Metadata

    Metadata is stored in Metadata Blocks, which are very similar to
    Data Blocks. Thus, the uncompressed size can be huge just like with
    Data Blocks. The difference is, that the contents of Metadata Blocks
    aren't given to the application as is, but parsed by liblzma. Still,
    reading through a huge Metadata can take very long time, effectively
    creating a denial of service like piping decoded a Data Block to
    another process would do.

    At first it would seem that using a memory limitter would prevent
    this issue as a side effect. But it does so only if the application
    requests liblzma to allocate the Extra Records and provide them to
    the application. If Extra Records aren't requested, they aren't
    allocated either. Still, the Extra Records are being read through
    to validate that the Metadata is in proper format.

    The solution is to limit the Uncompressed Size of a Metadata Block
    to some relatively large value. This will make liblzma to give an
    error when the given limit is reached.