In this case "make install" could fail if the man page directory
didn't already exist at the destination. If it did exist, a
dangling symlink was created there. Now the link is omitted
instead. This isn't the best fix but it's better than the old
behavior.
Add a note about failing "make check". The source of
the problem should be fixed in libtool (if it really is
a libtool bug and not mine) but I'm unable to spend time
on that for now. Thanks to Nelson H. F. Beebe for reporting
the issue.
Add a note about a possible need to run "ldconfig" after
"make install".
I don't know the details but I have an impression that there's
no problem in practice if using GCC since people have built xz
with GCC (without patching xz), but renaming the variable cannot
hurt either.
Thanks to Mark Ashley.
Previously, --block-list and --block-size only worked together
in threaded mode. Boundaries are specified by --block-list, but
--block-size specifies the maximum size for a Block. Now this
works in single-threaded mode too.
Thanks to James M Leddy for the original patch.
Now if --block-list is used in threaded mode, the encoder
won't need to flush at each Block boundary specified via
--block-list. This improves performance a lot, making
threading helpful with --block-list.
The flush timer was reset after LZMA_FULL_FLUSH but since
LZMA_FULL_BARRIER doesn't flush, resetting the timer is
no longer done.
Now --block-list=SIZES works with in the threaded mode too,
although the performance is still bad due to the use of
LZMA_FULL_FLUSH instead of the new LZMA_FULL_BARRIER.
Now liblzma only uses "mythread" functions and types
which are defined in mythread.h matching the desired
threading method.
Before Windows Vista, there is no direct equivalent to
pthread condition variables. Since this package doesn't
use pthread_cond_broadcast(), pre-Vista threading can
still be kept quite simple. The pre-Vista code doesn't
use anything that wasn't already available in Windows 95,
so the binaries should run even on Windows 95 if someone
happens to care.
Previously it was done in configure, but doing that goes
against the Autoconf manual. Autoconf requires that it is
possible to override e.g. prefix after running configure
and that doesn't work correctly if liblzma.pc is created
by configure.
A potential downside of this change is that now e.g.
libdir in liblzma.pc is a standalone string instead of
being defined via ${prefix}, so if one overrides prefix
when running pkg-config the libdir won't get the new value.
I don't know if this matters in practice.
Thanks to Vincent Torri.
When --flush-timeout=TIMEOUT is used, xz will use
LZMA_SYNC_FLUSH if read() would block and at least
TIMEOUT milliseconds has elapsed since the previous flush.
This can be useful in realtime-like use cases where the
data is simultanously decompressed by another process
(possibly on a different computer). If new uncompressed
input data is produced slowly, without this option xz could
buffer the data for a long time until it would become
decompressible from the output.
If TIMEOUT is 0, the feature is disabled. This is the default.
This commit affects the compression side. Using xz for
the decompression side for the above purpose doesn't work
yet so well because there is quite a bit of input and
output buffering when decompressing.
The --long-help or man page were not updated yet.
The details of this feature may change.
Testing for end of file was no longer correct after full flushing
became possible with --block-size=SIZE and --block-list=SIZES.
There was no bug in practice though because xz just made a few
unneeded zero-byte reads.
This switches units from microseconds to milliseconds.
New clock_gettime(CLOCK_MONOTONIC) will be used if available.
There is still a fallback to gettimeofday().
The man pages of lzmainfo, xzmore, and xzdec had similar
constructs as the man page of xz had before the commit
eb6ca9854b. Eric S. Raymond
didn't mention these man pages in his bug report, but
it's nice to be consistent.
Now both reading and writing should be without
race conditions with signals.
They might still be signal handling issues left.
Signals are blocked during many operations to avoid
EINTR but it may cause problems e.g. if writing to
stderr blocks when trying to display an error message.
