Now both reading and writing should be without
race conditions with signals.
They might still be signal handling issues left.
Signals are blocked during many operations to avoid
EINTR but it may cause problems e.g. if writing to
stderr blocks when trying to display an error message.
It is possible that a signal to set user_abort arrives right
before a blocking system call is made. In this case the call
may block until another signal arrives, while the wanted
behavior is to make xz clean up and exit as soon as possible.
After this commit, the race condition is avoided with the
input side which already uses non-blocking I/O. The output
side still uses blocking I/O and thus has the race condition.
POSIX says that fcntl(fd, F_SETFL, flags) returns -1 on
error and "other than -1" on success. This is how it is
documented e.g. on OpenBSD too. On Linux, success with
F_SETFL is always 0 (at least accorinding to fcntl(2)
from man-pages 3.51).
Due to a wrong variable name, when writing a sparse file
to standard output, *all* file status flags were cleared
(to the extent the operating system allowed it) instead of
only clearing the O_APPEND flag. In practice this worked
fine in the common situations on GNU/Linux, but I didn't
check how it behaved elsewhere.
The original flags were still restored correctly. I still
changed the code to use a separate boolean variable to
indicate when the flags should be restored instead of
relying on a special value in stdout_flags.
Input file can be a FIFO or something else that doesn't
support posix_fadvise() so don't check the return value
even with an assertion. Nothing bad happens if the call
to posix_fadvise() fails.
Now the following works as you would expect:
echo foo | xz > foo.xz
echo bar | xz >> foo.xz
( xz -dc --single-stream ; xz -dc --single-stream ) < foo.xz
Note that it doesn't work if the input is not seekable
or if there is Stream Padding between the concatenated
.xz Streams.
Spot candidates by running these commands:
git ls-files |xargs perl -0777 -n \
-e 'while (/\b(then?|[iao]n|i[fst]|but|f?or|at|and|[dt]o)\s+\1\b/gims)' \
-e '{$n=($` =~ tr/\n/\n/ + 1); ($v=$&)=~s/\n/\\n/g; print "$ARGV:$n:$v\n"}'
Thanks to Jim Meyering for the original patch.
Try to avoid overwriting the source file if --force is
used and the generated destination filename refers to
the source file. This can happen with 8.3 filenames where
extra characters are ignored.
If the generated output file refers to a special file
like "con" or "prn", refuse to write to it even if --force
is used.
xz didn't compress setuid/setgid/sticky files and files
with multiple hard links even with --force. This bug was
introduced in 23ac2c44c3.
Thanks to Charles Wilson.
The opening of the destination file is now delayed a little.
The coder is initialized, and if decompressing, the memory
usage of the first Block compared against the memory
usage limit before the destination file is opened. This
means that if --force was used, the old "target" file won't
be deleted so easily when something goes wrong very early.
Thanks to Mark K for the bug report.
The above fix required some changes to progress message
handling. Now there is a separate function for setting and
printing the filename. It is used also in list.c.
list_file() now handles stdin correctly (gives an error).
A useless check for user_abort was removed from file_io.c.
to stdout even if --force is used.
--force will still enable compression of symlinks, but only
in case they point to a regular file.
The new way simply seems more reasonable. It matches gzip's
behavior while the old one matched bzip2's behavior.
a regular file.
Sparse file creation can be disabled with --no-sparse.
I don't promise yet that the name of this option won't
change before 5.0.0. It's possible that the code, that
checks when it is safe to use sparse output on stdout,
is not good enough, and a more flexible command line
option is needed to configure sparse file handling.
Separate a few reusable components from XZ Utils specific
code. The reusable code is now in "tuklib" modules. A few
more could be separated still, e.g. bswap.h.
Fix some bugs in lzmainfo.
Fix physmem and cpucores code on OS/2. Thanks to Elbert Pol
for help.
Add OpenVMS support into physmem. Add a few #ifdefs to ease
building XZ Utils on OpenVMS. Thanks to Jouk Jansen for the
original patch.
